Nueva metodología para el diseño de tubos de hormigón estructural

Autor/a

Fuente Antequera, Albert de la .

Director/a

Aguado, Antonio

Codirector/a

Molins Borrell, Climent

Fecha de defensa

2011-10-14

Depósito Legal

B. 11999-2013

Páginas

169 p.



Departamento/Instituto

Universitat Politècnica de Catalunya. Departament d'Enginyeria de la Construcció

Resumen

The technical and economic suitability of using fibers has been proved in reinforced concrete pipes.However, the use of fibers in concrete pipe is slow, on the one hand due to the inertia to change in the construction field, and on the other hand due to the lack of a standardized, agile and reliable design method that accounts for the structural contribution of fibers. In this sense, this Doctoral Thesis aims to cover these aspects with regard to reinforced concrete pipes. For this purpose, a design method allows considering the strength contribution of the fibers in concrete pipes is proposed. Furthermore, in order to favour the spread of the results both to the scientific and the industrial community, the document of the Doctoral Thesis is presented as a compendium of articles accepted and / or in review status in scientific journals. Each of these articles presents the results of each of the lines of work and whose union has helped to achieve the main objective of this Doctoral Thesis. Firstly, the numerical tool Analysis of Evolutionary Sections (AES) developed to deal with the analysis of the strength response of reinforced concrete sections is presented. The tool is general and can simulate different reinforcement configurations (passive and/or active reinforcement with the possibility of incorporating fibers) and even the evolutionary construction of the section taking into account the rheological behaviour of materials. The model AES was subsequently used as a calculation tool of sections with the aim of addressing parametric studies as well as a subroutine into the other two models developed in the scope of this Doctoral Thesis. The second line of work focuses on the study of conventional reinforced concrete pipes. To address their optimal design the model Análisis de Tubos de Hormigón (ATH) has been developed. The practical interest of the model lies in the possibility of obtaining the optimal amount of reinforcement which meets the requirements in terms of bearing capacity specified in project. These reinforcements obtained from the models are, in most of the cases, inferior to the amounts in the design tables that are used traditionally. With the purpose of confirming the suitability of the ATH, an experimental campaign with tubes of 2800 mm of diameter has been carried out. By using the model, reductions up to 30% of the reinforcement have been obtained for pipes with the aforementioned diameter, while the differences in the bearing capacity do not exceed 10% when compared to the results of the three bearing edge test performed in the laboratory. The third and final line of work deepens into the technical and industrial side of the fiber reinforced concrete pipes. On the one hand, an extensive experimental campaign (some of it developed at the Universidade de São Paulo) is conducted, addressing issues associated with fiber reinforced concrete as well as others regarding the three edges test and the structural response of tubes of different diameters and with different amounts of fibers. On the other hand, the model for the Analysis of Pipes (MAP) was developed simultaneously for simulating the structural response of the fiber reinforced concrete pipes. The results of the bearing capacity of tubes up to 1000 mm of diameter tested have been compared with simulations performed with the MAP model, obtaining excellent correlations and not exceeding, in any case, the 5.5% relative error between the design loads. In view of the good results, it can be concluded that the design methodology herein presented, based on the use of the MAP model, ensures results that fit real behaviour and that the amounts of reinforcement provided are very close to the optimum necessary to meet the strength requirements established in each case.


El hormigón reforzado con fibras ha demostrado ser una alternativa atractiva frente al hormigón armado tradicional en numerosas tipologías estructurales. En los últimos diez años, los avances técnicos llevados a cabo en relación con este material han sido muy importantes, prueba de ello es que varios códigos normativos nacionales a nivel europeo ya han aceptado las fibras estructurales como material de refuerzo del hormigón, entre ellos la instrucción española EHE‐08 “Instrucción de Hormigón Estructural” en su Anejo 14. A pesar del escenario aparentemente positivo, la consideración de aporte resistente asociado al uso de las fibras es todavía anecdótica, lo cual no responde en la mayoría de las ocasiones a razones técnicas, sino a la gran inercia al cambio existente en el sector general de la construcción. Este es el caso de las tuberías de hormigón armado para redes de saneamiento. Se trata de una tipología estructural para la cual la idoneidad técnica y económica del uso de fibras ya se ha demostrado. Asimismo, también ha sido regulado por varias normativas nacionales específicas de tubos, entre éstas, la UNE‐EN 1916:2008 “Tubos y piezas complementarias de hormigón en masa, hormigón armado y hormigón con fibra de acero”. Sin embargo, el empleo de forma natural de fibras en tubos de hormigón está siendo lento, por una parte, debido a la inercia al cambio anteriormente citada, a lo que debe sumarse el hecho que pocas de las varias experiencias llevadas a cabo se han plasmado en la literatura técnica, y, por otra, a que no existe un método de diseño estandarizado, ágil y fiable al alcance de los proyectistas que permita tener en cuenta la incorporación de las fibras como material resistente. En esta dirección, la presente Tesis Doctoral tiene como objetivo cubrir estos aspectos asociados con los tubos de hormigón armado. Para ello, los trabajos llevados a cabo han permitido lograr distintos avances en relación con los tubos de hormigón armado tradicionales y los tubos de hormigón armado con fibras. Respecto a estos últimos, se propone el primer método para el diseño conocido hasta la fecha y que permite considerar la contribución resistente de las fibras. Además, de cara a maximizar la difusión de los resultados tanto hacia la comunidad científica como hacia la industrial, el documento de Tesis se plantea como un compendio de artículos aceptados y/o en estado de revisión en revistas científicas en los que se recogen los resultados específicos de cada una de las partes, cuya unión, ha permitido alcanzar el objetivo principal de esta Tesis Doctoral.

Materias

624 - Ingeniería civil y de la construcción en general; 69 - Materiales de construcción. Prácticas y procedimientos de construcción

Documentos

TAFA1de1.pdf

4.710Mb

 

Derechos

ADVERTIMENT. L'accés als continguts d'aquesta tesi doctoral i la seva utilització ha de respectar els drets de la persona autora. Pot ser utilitzada per a consulta o estudi personal, així com en activitats o materials d'investigació i docència en els termes establerts a l'art. 32 del Text Refós de la Llei de Propietat Intel·lectual (RDL 1/1996). Per altres utilitzacions es requereix l'autorització prèvia i expressa de la persona autora. En qualsevol cas, en la utilització dels seus continguts caldrà indicar de forma clara el nom i cognoms de la persona autora i el títol de la tesi doctoral. No s'autoritza la seva reproducció o altres formes d'explotació efectuades amb finalitats de lucre ni la seva comunicació pública des d'un lloc aliè al servei TDX. Tampoc s'autoritza la presentació del seu contingut en una finestra o marc aliè a TDX (framing). Aquesta reserva de drets afecta tant als continguts de la tesi com als seus resums i índexs.

Este ítem aparece en la(s) siguiente(s) colección(ones)